Pages

Sunday, July 07, 2024

How I constructed a Ruston(ish) diesel loco using a HGLW deluxe chassis kit

 After enhancing a Houston Gate Loco Works kit which I bought cheaply off eBay (see How I enhanced a basic HGLW loco kit) .....

..... I decided to have a go at constructing one of the neat little Ruston diesels which extensively pottered around various narrow gauge railways in the UK (and beyond). Having no drawings available, I scoured the net and eventually tracked down a pencil sketch of "Rusty" - one of the Rev. Awdry's Scarloey Railway locomotives.

I decided to base it around the ubiquitous Houston Gate Loco Works deluxe powered chassis as I was familiar with it, it is a tried and tested design and relatively cheap to buy. 

Having duly purchased the chassis kit online, I set about constructing it.

The instructions are clear and easy to follow and the laser-cut MDF parts, wheels, axles, gears, motor and electrical components needed are provided.

The first task was gluing the motor mounts to the cross-member .....

..... followed by the brake gear.

Then, one side was glued to the running-plate .....

.... followed by the other, trapping the cross member between them.

The ends of the chassis were then attached.

Following the instructions, two washers and the bearing bushes were slid on to the ends of the axles.

Next, the various components for the axle boxes were removed from the fret.


The spring hangers and axle boxes were glued on first, ....

...... followed by the axle box cover.

This process was repeated for all four axle boxes.

Semi-round nail-art gems ......

were then glued on to the brake hangers .......

..... axle boxes ......

..... and the irons.

My technique for applying the gems is to place a small blob of thick superglue on the desired locations, using a cocktail stick.

I find there is usually sufficient residue of glue left on the cocktail stick to allow me to pick up one of the gems and place it on the blob of glue. The blob is sufficiently more attractive than the residue on the stick, and so the gem is transferred easily on to the model.

Once all four axle boxes had been successfully adorned .......

..... the wheelsets with their bearings, were lowered in to the slots on either side of the chassis.
NOTE: The rubber O-Ring was left lying loosely over the axles at this point.


The axle boxes were then glued into place, making sure none of the glue came into contact with the bearings or axles.

This process was repeated until all four axle boxes were attached.

The O-Ring pulley could then be slid over the pulley wheels. I find this simple four-wheel drive mechanism to be very effective in practice.

The motor mounts were slid over the motos ......

..... and the motor screwed into place, using the screws provided.

As the holes for the screws are slotted, it was then possible to adjust the position of the motor, so the worm would mesh perfectly with the worm-wheel. I found attaching a 3v battery to the motor useful, so the motor position could be tweaked until there were minimal grinding sounds coming from the gears.

In the meantime, I had been busily designing, drawing and 3D printing the parts needed for the body. As the drawing of Rusty provided no scale or dimensions, I based the scaling around the HGLW chassis. I have since discovered that this means the loco is slightly larger than it should be - so maybe I will (one day) go back and redraw the parts to a more accurate scale using my own chassis (see below).

Once I had gathered all the parts of the body together, the first task was to remove the springs from above the axle-boxes on the chassis, so the body could slot over it.

I also needed to slightly widen the hole in the running plate for the motor with a file to enable it to fit.

The rear of the cab was glued into place first. The position of the cab front and rear are predetermined by slots and pegs which I included in the 3D drawings. 

Incidentally, I used EverBuild High Viscosity superglue for the construction of both the chassis and the body. It has the advantage of giving an almost instantaneous bond, especially if used in conjunction with an activator spray (all available from Tool Station).

The cab sides were then glued into place.


Then, the cab front was glued into place.

Next, the support for the fuel tank was attached in front of the cab, .......

..... allowing the tank to be glued on to it.

The ends of the tank were then glued on.

The bonnet was then attached, .......

..... followed by the bonnet cover.

The main part of the radiator was then glued on to the front of the bonnet, .......

...... followed by the two side pieces.

And finally, the top of the radiator was glued into place.

The body was then united with the chassis.

However, I wasn't very happy with its appearance. By this time I had tracked down some photos of actual Ruston locos, and it was obvious they sat a lot more closely to the rails than the HGLW chassis would allow.

It was time for a rethink.

Until now, I have fought shy of constructing my own mechanisms and chassis. Those I have constructed in the past have been only partially successful - or completely unsuccessful. However, fellow modellers on the gardenrails.org forum persuaded me to have a go at making my own chassis. The greatest problem I have faced previously with making powered chassis is my lack of precision when it comes to metalwork. Unless holes for axles are precisely aligned, then problems will ensue. But why make them from metal? Why not plastic? After all, the vast majority of commercial powered chassis and motor blocks I have used until now have used plastic mouldings for their main structures! And so, with a great deal of experimentation, trial runs, dead ends, redesigns and tweaking, I came up with a chassis which seems to be reasonably reliable and actually works! (see How I designed and developed my own powered loco chassis - pending)

Using this as a basis, I was able to mount the body much lower on the chassis

To my mind, although not strictly to scale, the loco looked a lot more realistic.

Furthermore, the powered chassis seemed to do what was required of it!

Buoyed with that success, the loco was taken through the paint shops and emerged in PLR livery, numbered 27, and given the name  'Nick' - another member of my "Old Gits' Friday Ambling Group (OGFAG)".




 It was also equipped with Micron Radio Control (compatible with Deltang) and a very cheap Chinese recordable soundcard on to which I uploaded the sound of a real Ruston chugging past.

For those who are interested, I have provided more information on how I designed, developed and produced my 3D printed powered chassis (pending) and the soundcard.

No comments:

Post a Comment